LY/T 3035-2018 車削類工具木柄

Turning tools wooden handles

LY/T 3043-2018 民族樂器鋸材 阮用材

National musical instrument sawn wood Ruan wood

LY/T 3038-2018 結構用木質材料術語

Structural wood material terminology

LY/T 3042-2018 民族樂器鋸材 柳琴用材

National musical instrument sawn timber Liuqin timber

LY/T 3033-2018 戶外用木材涂料人工老化試驗方法

Test methods for artificial aging of wood coatings for outdoor use

BS ISO 1997:2018 粒狀軟木和軟木粉 分類、性能及包裝

Granulated cork and cork powder. Classification, properties and packing

BS EN 1309-3:2018 圓木和鋸木.測量方法.特征與生物降解

Round and sawn timber. Methods of measurements. Features and biological degradations

DB44/T 2123-2018 生長錐取樣木材密度測定方法

本標準規定了利用生長錐取樣測定木材密度的設備、方法和測定結果與報告等要求。 本標準適用于木材密度的測定。

Method for Determining Density of Wood from Growth Cone Sampling

DIN EN 1309-3:2018 圓木和鋸木.測量方法.第3部分:特征和生物降解

This European Standard specifies the methodology for measurement of features - in relation to wood structure, biological agencies and other damage - taken into account in the visual grading: a) for appearance - of sawn, processed and round timber; b) for serviceability - of sawn and processed timber (identified in EN 1611-1 as the integrity of the timber). When the standard is applied the methodology of measurement used shall be stated. It is not applicable to structural timber for which strength grading in accordance with EN 14081-1 is required. This standard applies to hardwood and softwood sawn timber, both square edged and un-edged, to processed timber and to round timber. It does not apply to tropical timber.

Round and sawn timber - Methods of measurements - Part 3: Features and biological degradations; German version EN 1309-3:2018

LY/T 1507-2018 木桿

本標準規定了木桿樹種、尺寸、材質指標、檢驗方法及材積計算等。 本標準適用于全國木材生產、流通領域的農具、工具、棚架、木制構件及礦扒條用料等。

Wood pole

DIN EN 14298:2018 鋸材.干燥質量的評定;德文版本EN 14298-2017

This European Standard defines a method of assessment of drying quality. It applies to a lot of dried sawn timber (surfaced or not). It applies to both softwood and hardwood with a thickness not greater than 100 mm. The quality of drying is expressed in terms of target and average moisture content of the lot as well as defining the moisture content variation between individual pieces expressed as allowable upper and lower limits. An option for specifying the degree of case-hardening is included. NOTE 1 Other features related to drying, e. g. checking, distortions, stain, etc., are specified in documents for visual grading of sawn timber or in product specifications and are not covered by this document. NOTE 2 In the following the term sawn timber is used for all dried timber covered by this the scope.

Sawn timber - Assessment of drying quality; German version EN 14298:2017

DIN EN 14354:2017 木質板條.木質薄板地板覆蓋物;德文版本EN 14354-2017

This European Standard defines terms and specifies requirements and test methods for wood veneer floor coverings with multilayer built up for internal use. It gives guidance for the evaluation of conformity of the products to the requirements of this standard. This European Standard is not applicable to multilayer parquet elements with a minimum top layer thickness of 2,5 mm. For these products EN 13489 applies.

Wood-based panels - Wood veneer floor coverings; German version EN 14354:2017

BS 5756:2007+A2:2017 溫帶硬木的視覺強度等級規范

Visual strength grading of temperate hardwood-Specification

ISO 13061-12:2017 木材的物理和機械性能.潔凈木材小樣品試驗方法.第12部分: 靜硬度測定

This document specifies a method for determining of the static hardness of wood by measuring resistance of a test piece to the penetration of a plunger under gradually increasing load.

Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 12: Determination of static hardness

ISO 13061-11:2017 木材的物理和機械性能.潔凈木材小樣品試驗方法.第11部分: 沖擊壓痕阻力測定

This document specifies a method for the determination of the resistance of wood to impact indentation by a steel ball.

Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 11: Determination of resistance to impact indentation

ISO 13061-10:2017 木材的物理和機械性能.潔凈木材小樣品試驗方法.第10部分: 沖擊彎曲強度測定

This document specifies a method for determining the impact bending strength of wood.

Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 10: Determination of impact bending strength

ISO 4708:2017 復合軟木.襯墊材料.試驗方法

This document specifies test methods to determine the characteristics of agglomerated composition cork and rubbercork to be used as gaskets in the mechanical industry. The following characteristics are considered: — thickness, — apparent density, — tensile strength, — compressibility and recovery, — flexibility, — resistance to boiling water, — behaviour in fluids.

Composition cork - Gasket material - Test methods

LY/T 2885-2017 竹百葉窗簾

bamboo blinds

LY/T 2872-2017 木制珠串

wooden bead string

LY/T 2873-2017 鉛筆板

pencil board